As the performance of mobile phones is getting stronger and stronger, the consequent lack of mobile phone life is gradually becoming insufficient. We are gradually getting used to bringing a mobile power supply when we go out. Although it is possible for mobile phone manufacturers to increase the battery capacity that directly determines the battery life, but this will increase the thickness and weight of the mobile phone, so mobile power has become an indispensable accessory in our lives. However, with the development of mobile phone fast charging technology in recent days, it is enough to go out with a charger. It takes only a short five to ten minutes to meet the demand for mobile phone power for a long time. It is necessary to appear. Meizu launched the new Meizu PRO 6 in the high-end PRO series in mid-April, and the charger equipped with Meizu PRO 6 is the best conscience charger in the industry.
Why do you say that? Although the surface of the Meizu PRO 6 charger UP0830 looks like the same as the Meizu PRO 5 charger UP1220, in fact, UP0830 is not only a little bit of improvement for internal technology. From the text information on the charger, the UP0830 supports up to 8V 3A or 12V 2A output standards, which means that the charger's output power has reached 24W. The high output power of 15W to 24W also ensures that Meizu PRO 6 can be fully charged in a very short time. According to the official introduction of Meizu, charging Meizu PRO 6 can charge about 24% of electricity in 10 minutes, and the full Meizu is full. The PRO 6 only takes one hour.
If you disassemble the Meizu PRO 6 charger, we can also be surprised to find that the UP0830 actually supports the MTK PEP2.0 charging protocol and also supports the Qualcomm QC3.0 charging protocol, which means the charger of Meizu PRO 6 It is a dual-protocol fast charging charger, which can be supported by both QC3.0 and MTK PEP. This is very rare in the current mobile phone market. It can be seen that the Meizu PRO 6 charger has many consciences. This means that in addition to Meizu PRO 6 can be charged with UP0830, such as Xiaomi 5, LG G5, HTC 10 and other mobile phones using Qualcomm QC3.0 fast charge protocol can use this charger for fast charging, and the charging efficiency of UP0830 More expensive than the original charger for these phones, simply put a UP0830 to get countless chargers off the job.
In addition to the extremely high charging efficiency, the UP0830 has an insulating plastic sheet on the other side of the board to isolate high and low voltage, and there is also a high voltage protection resistor. When the voltage is too high, the resistor will be broken down to cause a short circuit, and then charged. The fuse inside the unit will be blown, so that the battery of the mobile phone can be protected from any harm. And this charger also has precise control current, intelligent switching high and low voltage function, to ensure the hardware security of the mobile phone and the user's personal safety.
According to the hardware engineer of Meizu, the Meizu PRO 6 charger adopts the design of two charging chips, and has triple insurance in terms of charging safety: dynamically adjusted by customized Texas Instruments power control chip and self-developed fast charging algorithm. Charging voltage; set the thermostat in the USB Type-C part to control the charging current in real time; increase the high-temperature active power-off device on the data line circuit board to protect the battery safety. At the same time, Meizu engineers drastically reduced the temperature during fast charging, which is 3-5 degrees lower than the temperature of other brands' fast charging and charging, which reduces the aging of mobile phone hardware caused by high temperature. It can be seen that the Meizu PRO 6 charger not only has a fast charging speed, but is also safe enough to use.
Looking back, the iPhone users are still using the old 5V1A charger, while the domestic brands such as Meizu have already used the fast charge charger. It can be seen that the users of Meizu PRO 6 are indeed much more happy. Fast charging is something that has nothing to do with performance, but it is the most practical technology for consumers.
Industrial Main Board Cable:SCSI,D-SUB,DVI,Wire to Wire ,RJ45...
There are five types of main board power line interface, and different external devices correspond to different interfaces. Different interfaces and their connecting pins are also different. For example, the pin of the main power supply is 24 pins, and the hard disk drive is 5 pins.
1. 20pin + 4Pin interface: it is a common interface combination, in which 20pin is the main power interface and 4Pin is the auxiliary power supply interface.
2. 5pinsata interface: special interface for power supply of hard disk and optical drive.
3. 6pin? PCI? Express connector: a special interface for independent graphics power supply.
4. 4Pin connector: it is a kind of floppy disk power connector, which is used to power the floppy drive equipment.
5. 4Pin power interface: optical drive, old IDE hard disk and peripheral hardware power supply interface.
Industrial Main Board Cable
ShenZhen Antenk Electronics Co,Ltd , https://www.antenk.com